top of page

Bronzed Babez Group

Public·11 members
Lucas Miller
Lucas Miller

Gionee F103 Pro Firmware ROM: How to Download and Install


How to Download and Install Gionee F103 Pro Flash File




If you own a Gionee F103 Pro smartphone and want to update its software, fix some issues, or unlock its features, you may need to download and install a flash file on your device. A flash file is a package that contains the official firmware (operating system) of your phone. By flashing your phone with a flash file, you can restore it to its original state, remove any bugs or errors, improve its performance, and enhance its security. In this article, we will show you how to download and install the Gionee F103 Pro flash file in a few easy steps.




gionee f103 pro flash file download



Introduction




The Gionee F103 Pro is a budget-friendly smartphone that was launched in 2016. It features a 5-inch IPS LCD display, a quad-core MediaTek MT6735 processor, 3 GB of RAM, 16 GB of internal storage, a 13 MP rear camera, a 5 MP front camera, a fingerprint sensor, and a 2400 mAh battery. It runs on Android 6.0 Marshmallow with Amigo 3.2 user interface.


However, like any other smartphone, the Gionee F103 Pro may experience some problems over time, such as slow performance, boot loop, software glitches, network issues, or battery drain. These problems can be solved by flashing your phone with the official firmware. Flashing is also useful if you want to upgrade your phone's software, unroot your phone, or remove any custom ROMs or mods that you have installed.


Before you proceed to flash your phone, you should know that flashing is a risky process that may void your warranty, erase your data, or damage your phone if not done properly. Therefore, you should follow the instructions carefully and take all the necessary precautions. You should also backup your data before flashing, as flashing will wipe out everything on your phone.


Requirements




To flash your Gionee F103 Pro successfully, you will need the following:


  • A Windows PC or laptop.



  • A USB cable to connect your phone to your PC.



  • A fully charged battery or at least 30% battery level on your phone.



  • A backup of your data on your phone or an external device.



  • The Gionee F103 Pro flash file that matches your phone's model and region.



  • The SP Flash tool that allows you to flash the firmware on your phone.



  • The USB driver that enables your PC to recognize your phone.



Steps




Now that you have everything ready, you can follow these steps to flash your Gionee F103 Pro:


gionee f103 pro firmware download


gionee f103 pro stock rom flash file


gionee f103 pro official firmware update


gionee f103 pro flash tool download


gionee f103 pro android scatter file


gionee f103 pro t6524 flash file


gionee f103 pro t6517 flash file


gionee f103 pro t5907 flash file


gionee f103 pro t5741 flash file


gionee f103 pro t5370 flash file


gionee f103 pro sp flash tool


gionee f103 pro mtk driver


gionee f103 pro usb driver


gionee f103 pro flashing guide


gionee f103 pro software update


gionee f103 pro hard reset


gionee f103 pro boot loop fix


gionee f103 pro unbrick solution


gionee f103 pro imei repair


gionee f103 pro frp bypass


gionee f103 pro root access


gionee f103 pro custom rom


gionee f103 pro twrp recovery


gionee f103 pro nougat update


gionee f103 pro oreo update


gionee f103 pro pie update


gionee f103 pro android 10 update


gionee f103 pro android 11 update


gionee f103 pro latest firmware version


gionee f103 pro original firmware download


gionee f103 pro tested flash file


gionee f103 pro free flash file download


gionee f103 pro fastboot mode


gionee f103 pro recovery mode


gionee f103 pro download mode


gionee f103 pro factory reset protection


gionee f103 pro google account verification


gionee f103 pro pattern lock remove


gionee f103 pro pin lock remove


gionee f103 pro password lock remove


gionee f103 pro screen lock remove


gionee f103 pro hang on logo fix


gionee f103 pro dead boot repair


gionee f103 pro white screen fix


gionee f103 pro black screen fix


gionee f103 pro blue screen fix


gionee f103 pro touch screen fix


gionee f103 pro camera fix


gionee f103 pro wifi fix


  • Backup your data and charge your battery. As mentioned earlier, flashing will erase all your data on your phone, so make sure you have a backup of everything important on your phone or an external device. You can use Google Drive, Google Photos, or any other cloud service to backup your data online. You can also use a USB cable to transfer your data to your PC or laptop. You should also charge your battery to at least 30% or more to avoid any interruptions during the flashing process.



  • Install the USB driver and the SP Flash tool on your PC. You will need the USB driver to ensure that your PC can communicate with your phone. You can download the USB driver for Gionee F103 Pro from here. After downloading, extract the zip file and run the setup.exe file to install the driver on your PC. You will also need the SP Flash tool to flash the firmware on your phone. You can download the SP Flash tool from here. After downloading, extract the zip file and run the flash_tool.exe file to launch the tool.



  • Download the Gionee F103 Pro flash file from the official website. You will need the flash file that matches your phone's model and region. You can download the official flash file for Gionee F103 Pro from here. After downloading, extract the zip file and locate the scatter file inside. The scatter file is a text file that contains the information of all the partitions of your phone's firmware.



  • Extract the flash file and load the scatter file on the SP Flash tool. On the SP Flash tool, click on the Download tab and then click on the Choose button next to Scatter-loading File. Browse to the folder where you extracted the flash file and select the scatter file. The SP Flash tool will load all the firmware files automatically. Make sure that all the files are checked and that none of them are grayed out.



  • Connect your Gionee F103 Pro to your PC and start the flashing process. Before you connect your phone to your PC, you need to turn it off and remove its battery (if it is removable). Then, press and hold the Volume Down button and connect your phone to your PC using a USB cable. The SP Flash tool will detect your phone and start flashing it. You will see a red bar, followed by a yellow bar, followed by a green circle on the SP Flash tool. This means that the flashing process is completed successfully.



  • Verify the successful installation of the flash file on your Gionee F103 Pro. After flashing, disconnect your phone from your PC and insert its battery (if it is removable). Then, turn on your phone and wait for it to boot up. It may take a few minutes for the first boot, so be patient. Once your phone is on, you can check its settings and see if everything is working fine. You can also check its software version and see if it matches with the flash file that you downloaded.



Troubleshooting




Sometimes, you may encounter some problems or errors while flashing your Gionee F103 Pro. Here are some common ones and how to fix them:


  • If you get an error message like "BROM ERROR: S_FT_ENABLE_DRAM_FAIL (4032)" or "PMT changed for the ROM; it must be downloaded", it means that you have selected a wrong scatter file or a wrong flash file for your phone. To fix this, you need to download and use the correct flash file that matches your phone's model and region.



  • If you get an error message like "BROM ERROR: S_DA_SDMMC_WRITE_FAILED (3149)" or "BROM ERROR: S_FT_DOWNLOAD_FAIL (4008)", it means that there is a problem with your USB connection or your phone's battery level. To fix this, you need to check if your USB cable is working properly, if your USB port is clean and not damaged, if your phone's battery is charged enough, and if you have installed the correct USB driver on your PC.



  • If you get an error message like "BROM ERROR: S_NOT_ENOUGH_STORAGE_SPACE (1011)" or "BROM ERROR: S_SECURITY_SF_CODE_COMMAND_FORBIDDEN (6126)", it means that there is not enough space on your phone's internal storage or that there is a security lock on your phone's bootloader. To fix this, you need to delete some files from your phone's internal storage or unlock its bootloader before flashing.



Conclusion




In this article, we have shown you how to download and install the Gionee F103 Pro flash file in a few easy steps. By flashing your phone with the official firmware, you can update its software, fix some issues, or unlock its features. However, flashing is a risky process that may void your warranty, erase your data, or damage your phone if not done properly. Therefore, you should follow the instructions carefully and take all the necessary precautions. You should also backup your data before flashing, as flashing will wipe out everything on your phone. We hope that this article has helped you to flash your Gionee F103 Pro successfully. If you have any questions or feedback, please feel free to leave a comment below.


FAQs




Here are some frequently asked questions and answers related to the topic of Gionee F103 Pro flash file download:


Q: What is the difference between flashing and updating?


  • A: Flashing is the process of installing a new firmware on your phone, while updating is the process of downloading and installing a newer version of the existing firmware on your phone. Flashing is usually done manually, while updating is usually done automatically or with a notification.



Q: How can I check the software version of my Gionee F103 Pro?


  • A: You can check the software version of your Gionee F103 Pro by going to Settings > About Phone > Software Information. You will see the Android version, the Amigo version, and the build number of your phone.



Q: How can I backup my data on my Gionee F103 Pro?


  • A: You can backup your data on your Gionee F103 Pro by using Google Drive, Google Photos, or any other cloud service to backup your data online. You can also use a USB cable to transfer your data to your PC or laptop. You can also use a microSD card to backup your data on your phone.



Q: How can I unlock the bootloader of my Gionee F103 Pro?


  • A: You can unlock the bootloader of your Gionee F103 Pro by following these steps: - Enable Developer Options on your phone by going to Settings > About Phone > Tap on Build Number seven times. - Enable USB Debugging and OEM Unlocking on your phone by going to Settings > Developer Options > Toggle on USB Debugging and OEM Unlocking. - Connect your phone to your PC using a USB cable and open a command prompt window on your PC. - Type "adb devices" and press enter to check if your phone is recognized by your PC. - Type "adb reboot bootloader" and press enter to reboot your phone into bootloader mode. - Type "fastboot devices" and press enter to check if your phone is recognized by your PC in bootloader mode. - Type "fastboot oem unlock" and press enter to unlock your bootloader. You will see a confirmation message on your phone's screen. Press the Volume Up button to confirm and the Power button to reboot.



Q: How can I root my Gionee F103 Pro?


  • A: You can root your Gionee F103 Pro by following these steps: - Download the Magisk zip file from here and copy it to your phone's internal storage or microSD card. - Download the TWRP recovery image for Gionee F103 Pro from here and copy it to your PC. - Connect your phone to your PC using a USB cable and open a command prompt window on your PC. - Type "adb devices" and press enter to check if your phone is recognized by your PC. - Type "adb reboot bootloader" and press enter to reboot your phone into bootloader mode. - Type "fastboot devices" and press enter to check if your phone is recognized by your PC in bootloader mode. - Type "fastboot flash recovery twrp.img" and press enter to flash the TWRP recovery image on your phone. Replace twrp.img with the name of the TWRP recovery image that you downloaded. - Type "fastboot reboot" and press enter to reboot your phone normally. - Press and hold the Volume Up and Power buttons simultaneously to boot into TWRP recovery mode. - Tap on Install and browse to the Magisk zip file that you copied earlier. Swipe to confirm the installation. - Tap on Reboot System and wait for your phone to boot up normally.





About

Welcome to the group! You can connect with other members, ge...

Members

bottom of page